Room Alert Produto | Sensors

Extreme Reduced Temperature

• Extreme low temperature sensor in real time
• Temperature range: -328 ̊- 32 ̊ F, -200 ̊- 0 ̊ C
• Analogue, 1-5 VDC
• Standardization sensor Dn IEC 751 Class B
• Room Alert 32E / W, 12E and Digital Temperature and Analog Sensor compatible

Low Extreme Temperature

• Real-time extreme low temperature sensor
• Temperature range: -328 ̊- 32 ̊ F, -200 ̊- 0 ̊ C
• Analog, 1-5 VDC Dn IEC 751 Class B standardization sensor
• Compatible with Room Alert 32E/W, 12E and Digital
• Temperature Sensor and Analog

Digital humidity

• Provides real-time temperature values from -40 to 85 degrees Celsius
• Accuracy is within +/- 2 C degrees
• The humidity range is 5% to 95% relative humidity (RH) without condensation.
• The humidity accuracy is within +/- 4.5% RH at 5 to 59% RH and within +/- 6.5% RH at 60 to 95% RH
• This is a dynamic sensor that provides temperature and humidity values every two seconds and sends real-time temperature and humidity alert data back to Room Alert ID box for data logging.
• Alerts and automatic corrective actions.
• Instant ‘Plug & Play’ sensor that can be connected via one of the standard RJ-11 sockets on any compatible Room Alert monitor.

Types

Room Alert offers this sensor with cable lengths of 25 ‘, 50’ and 100 ‘.

Main Power / UPS

• Real-time power on / off status
• Monitors main power, UPS or single phase
• Maximum sensor cable distance up to 900 ‘, includes 25’
• Compatible with Room Alert 32E / W, 26E / W, 24E, 12E, 11E, 7E, 4E, 3E, 3W, WiSH and WiSPR.

Power Current (Amps)

• Monitors the electric current passing through a single-phase powered cable.
• Monitor output: 0-10A, 0-20A and 0-50A.
• Connects via Room Alert Analog Sensor Port or Digital Temperature and Analog Sensor.
• Operates at 0-95% RH, non-condensing environment.
• Low voltage 2-wire cable connection.
• Compatible with Room Alert 32E / W, 12E and Digital Temperature and Analog Sensor.

Active power and temperature

• Provides real-time power status information for any AC powered device, simply by tying to an existing power cord
• Power is considered ‘active’ when it is greater than approximately 100W
• Accuracy is within +/- 2.5 watts
• This sensor provides real-time temperature values from -40 ° to 85 ° Celsius
• Accuracy is within +/- 2 C degrees

Types
Digital Active Power sensors W / temperature 10` 25` 50` and 100`

Flood / water cable

• Used to extend the existing Flood Cable Sensor configuration.
• This extender is connected in line between the leading cable and the existing water detection cable.
• This flood cable extension requires a flood sensor with a 50 ‘flood sensor cable and a lead cable.
• The flood sensor cable can be extended even further by adding one or more 50 ‘flood cable extenders.

Movement

• Motion detection device specially equipped with additional electronic components that interface with any compatible Room Alert ID box
• Powered by a 12V DC power supply and is designed to detect movement up to 35 ‘(feet) apart with a cone cover approximately 84 degrees wide
• This is an instant Plug & Play sensor that can be connected via one of the sensor channels on the back of any compatible Room Alert ID box
• The cable distance can be extended from the standard 25 ‘to approximately 900’ using the standard speaker wire, twisted pair or any reliable low voltage 2-wire cable.

• Specially equipped motion detection device with additional electronic components that interface with any compatible Room Alert ID box
• Powered by a 12V DC power supply and designed to detect movement up to 35′(feet) away with a cone cover of approximately 84 degrees wide
• This is an instant ‘Plug & Play’ sensor that can be connected through one of the sensor channels on the back of any compatible Room Alert ID box
• The cable distance can be extended from standard 25′ to approximately 900′ using the standard speaker wire, twisted pair or any reliable low voltage 2-wire cable.

• Motion detection device specially equipped with additional electronic components that allow interfacing with any Room Alert ID box compatible
• Powered by a 12V DC power supply and is designed to detect motion up to 35′(feet) away with a cone coverage of approximately 84 degrees wide
• This is an instant ‘Plug & Play’ sensor that can be connected through one of the sensor channels on the back of any Room Alert ID box compatible
• The cable distance can be extended from the standard 25′ to approximately 900′ using standard speaker wire, twisted pair, or any reliable low voltage 2-wire cable.

Room / door intrusion

• Provides real-time recognition of a door or cabinet being opened
• The standard of use is to mount the wired sensor in the frame of a door, then mount the corresponding actuator in front of the sensor on the door itself and when the door opens, the two components separate and the sensor fires
• This is an instantaneous Plug and Play room / door intrusion sensor that can be connected via one of the key sensor channels on the back of any compatible Room Alert ID box
• The cable distance can be extended from the standard 25 ‘to approximately 900’ using the standard speaker wire, twisted pair or any reliable low voltage 2-wire cable.

Air flow (NC / NO)
(NC)

• Provides real-time recognition of airflow stop
• This airflow sensor is normally closed and includes a mounting clip and clamp
• Typical use is to measure airflow in an HVAC duct, under an elevated floor or close to a fan in an important rack or server cabinet.

(NO)

• Provides real-time recognition of airflow stop
• This sensor is normally open and includes a mounting clip and clip
• Typical use is to monitor continuous airflow in an HVAC duct, under an elevated floor, or near a fan in an important rack or server cabinet.

Panic buttons

• Designed to be used as an emergency alarm to provide warning when someone is working and may need help or conditions to reach an alarm state.
• Palm or foot size, locks in place, pull to release.
• NEMA classification for climate and industrial use.
• Compatible with Room Alert 32E / W, 26E / W, 24E, 12E, 11E, 7E, 4E, 3E, 3W, WiSH and WiSPR

Wireless sensor concentrators

• It is a wireless hub that is used exclusively to transmit data from internal and connected sensors to the 32W or 26W environment monitoring hardware unit and WiSPR sensors
• As the WiSH sensor is wireless, it can be found anywhere you want to monitor up to almost 250 ‘(in the ideal environment) of the main unit without having to run cables.

Light towers and more

• Designed to enhance the alert capabilities of Room Alert 32W, 32E, 12E, 4E or 3E monitors to include visual and audible alarm when a problem or event occurs
• The visual alarm warning lights and audio alerts can also be enabled or disabled automatically or manually via the Room Alert web interface, Room Alert device management software and SNMP Trap or SNMP Set commands
• Any Room Alert or Axis camera on the network can enable or disable lights or audio
• The light and audio tower does not need to be connected to this unit
• This ability allows the Light Towers to be mounted in any location where the lights are highly visible and triggered through the network.
• The lights can be activated by alarm, connected sensors and other devices remotely over the network.

Analog sensors

• Monitors the internal temperature of the environment and an analog sensor connected from 0 to 5 VDC
• This compact and lightweight sensor has a range of -40º to 185º Fahrenheit (-40º to 85º Celsius) and from 0 to 5 VDC
• Has accuracy within +/- 2º C and +/- 0.075 volts.

Relay Switches

• Allows low voltage devices to be turned on / off in response to an event that enters or leaves an alarm condition
• The Sensor Relay Switch supports up to 4 devices with visible relay status lights
• Each relay supports loads of up to 0.3A at 125VAC or 1A at 24VDC.

Network cameras

• Install network cameras anywhere to get a real-time view of what’s going on in your computer room, data center or other facility
• Use with Room Alert Device Manager software to send instant photos with alerts, display real-time video to multiple cameras simultaneously from a single IP address and incorporate camera sensors
• Use with your Room Alert account to see instant images triggered by motion detection from anywhere via your favorite browser
• Take advantage of features that enhance your physical environment monitoring.